The aim of this work was to determine TTT diagram of medium carbon V-N micro-alloyed steel with emphasis on the

development of intragranular ferrite morphologies. The isothermal treatment was carried out at 350, 400, 450, 500, 550

and 600 οC. These treatments were interrupted at different times in order to analyze the evolution of the microstructure.

Metallographic evaluation was done using optical and scanning electron microscopy (SEM). The results show that at high

temperatures (≥ 500 ○C) polygonal intragranulary nucleated ferrite idiomorphs, combined with grain boundary ferrite and

pearlite were produced and followed by an incomplete transformation phenomenon. At intermediate temperatures (450, 500

○C) an interloced acicular ferrite (AF) microstructure is produced, and at low temperatures (400, 350 ○C) the sheave of

parallel acicular ferrite plates, similar to bainitic sheaves but intragranularly nucleated were observed. In addition to sheaf

type acicular ferrite, the grain boundary nucleated bainitic sheaves are observed.

A numerical scheme for computing compressible multi-component flows is examined. The numerical approach is based on a mathematical model that considers interfaces between fluids as numerically diffused zones. The hyperbolic problem is tackled using a high-resolution HLLC scheme on a fixed Eulerian mesh. The scheme for the non-conservative terms is derived to fulfill the interface condition. The results are demonstrated for several one and two-dimensional test cases.

The electron-doped magnetic nanoparticles of Ca1–xYxMnO3 (x = 0, 0.05, 0.10, 0.15, 0.20,

and 0.30) manganite with an average particle size of 50 nm are analyzed and discussed in relation to their bulk counterparts. Nanoparticle samples show dominant anti-ferromagnetic ordering with a significant increase of coercivity, with the maximum value of 0.9 T for x = 0.

Par ti cle size re duction in Ca1–xYxMnO3 retains the bulk-like magnetic behavior of samples

having up to 15% of Y3+, with the small fer ro mag netic contri bu tion from dis or dered sur face

spins. Sup pres sion of charge order ing state and en hance ment of sat ura tion mag ne ti zation

were found in samples with higher Y3+ con cen tra tion (x = 0.2, 0.3), indicating high ferromag netic contri bu tion in these sam ples

A new synthesis route for obtaining a single-phase hexagonal YMnO3 was developed, based on the annealing of the amorphous

precursor powder obtained by the glycine–nitrate combustion method. The process was monitored by XRD as well as by magnetic and

heat capacity measurements. The analysis of these data shows that precursor powder undergoes a gradual phase transformation that

depends on the annealing temperature. The metastable orthorhombic YMnO3 phase is the first to appear at temperatures below 700 1C,

while a mixture of ortho- and hexa-phases was found to exist within the 700–900 1C range. An almost complete conversion to hexaphase occurs at 900–1000 1C, but to obtain the pure, well crystallized h-YMnO3 phase an annealing temperature of 1300 1C was

necessary. The synthesis method applied in this work has been proved to be more convenient for obtaining single-phase h-YMnO3 than

by a solid state reaction. In addition, it is capable of producing sample free of parasitic phases that are often present in specimens

obtained by other synthesis methods.

Van Siclen (1988 Am. J. Phys. 56 1142) reported a curious property of a dielectric sphere in the field of an external point charge: the field outside the sphere generated by the combination of the original charge exterior and the Kelvin image charge interior to the sphere is independent of the permittivity of the sphere. In this paper, we simplify and correct the original derivation and give a detailed analysis of the sources of the field. We also present various checks for the theory, providing instructive exercises for advanced undergraduates.

Fuzzy decision forests aim to improve the predictive power of single fuzzy decision trees by allowing multiple views of the same domain to be modelled. Such forests have been successfully created for classification problems where the outcome field is discrete; however predicting a continuous output value is more challenging in combining the output from multiple fuzzy decision trees. This paper presents a new approach to creating fuzzy regression tree forests based upon the induction of multiple fuzzy regression decision trees from one training sample, where each tree will represent a different view of the data domain. The singular fuzzy regression trees are induced using a proven algorithm known as Elgasir which fuzzifies crisp CHAID decision trees using trapezoidal membership functions for fuzzification and applies Takagi-Sugeno inference to obtain the final predicted values. A modified version of Artificial Immune System Network model (opt-aiNet) is then used for the simultaneous optimization of the membership functions across all trees within the forest. A strength of the proposed method is that data does not require fuzzification before forest induction this reducing pre-processing time and the need for subjective human experts. Five problem sets from the UCI repository and KEEL repository are used to evaluate the approach. The experimental results have shown that fuzzy regression tree forests reduce the error rate compared with single fuzzy regression trees. 

Problem statement: In the construction industry, success of building projects greatly depends on the client’s performance. The performance of clients is crucial since decisions made will influence the overall project performance. Typically, clients are represented by managerial and technical representatives during the design process. They play major roles in conveying required information to the design team regarding their future project. The quality of clients’ representatives has potential influence on design team performance. In designing green buildings client’s attributes are critical factors to high performance of building projects. Attributes such as knowledge and experience on green buildings, commitment level to green and clients’ ability to participate and manage design process are the key factors to produce green design. The propose of this study to identify current performance level of clients of building projects and establish key clients’ attributes influencing green design performance. Approach: To achieve mentioned aim a questionnaire survey was conducted to collect dada required. A sample of 274 respondents has been covered under the study, including architects and engineers practicing design and consultancy building sectors. Prior to analysis of data WINSTEPS software were used for Rasch modeling to determine validity and reliability of date. Descriptive analysis data includes quantitative and qualitative. Results and Conclusion: Client qualities in general were low, client communication with design team; client involvement and ability to coordinate design process were moderate. However, Knowledge and experience on green …